Solar Water Heater Elements

Solar water heater elements provide electric backup heating for solar hot-water tanks when solar energy alone is insufficient. They install into compatible tank connections and heat the stored water directly.

Select the correct thread, voltage, wattage, element length and material for the tank. Confirm clearance, sealing and controller compatibility before installation.

Solar Water Heater Elements
Filter by
Price
$ $
Voltage
Power
more... less
Tube Length
more... less
Tube Material
Thread Size
based on review(s)
No reviews yet
Threaded Solar Water Heating Element with Probe Hole and BSP Thread Ref: AH100009

Threaded solar water heating element featuring a 1-inch BSP connection, probe hole, and multiple power options.

110 V / 220 V / 380 V 1 kW / 2 kW / 3 kW / 4 kW 180 mm / 210 mm / 230 mm / 260 mm
$60.95
Custom made

Need an exact replacement?

Send dimensions, voltage, power, material, and photos. We’ll manufacture a heating element for your application.

Fill out the form
based on review(s)
No reviews yet
1 Inch Threaded Solar Electric Water Heater Heating Element 220V Ref: AH100192

AC220V electric heating element for solar water heaters and tanks, featuring 304 stainless steel construction and 1-inch threaded mounting.

AC 220 V 1500 W / 2000 W 304 Stainless Steel
$143.38
based on review(s)
No reviews yet
Electric Immersion Water Heating Element DN32 1.25 Inch 220/380V for Solar Water Heaters Ref: AH100250

Electric immersion water heating element with a DN32 threaded connection for solar water heaters and liquid heating applications.

220 V / 380 V (Across offered models) 3 kW / 4.5 kW / 6 kW / 9 kW / 12 kW (Across offered models) 190 mm / 210 mm / 250 mm / 290 mm / 355 mm (Across offered models)
$108.05
based on review(s)
No reviews yet
DN25 1-Inch BSP Threaded Immersion Water and Oil Heating Element Ref: AH100289

Threaded immersion heating element with 304 stainless steel tube and thread, suitable for water tanks, boilers, and oil stoves.

110 V / 220 V / 380 V 1 kW / 2 kW / 3 kW / 4 kW 180 mm / 210 mm / 230 mm / 260 mm
$148.98
Showing 1-11 of 15 item(s)
Selection help

Frequently asked questions

Practical guidance for choosing and using products in this category.

Can an immersion heater be switched on without liquid?

An element designed for immersion must not be energised with its heated section exposed to air. Keep the required heated length covered by the specified liquid throughout operation, following the product instructions. Dry operation can cause rapid overheating and element failure.

Temperature control and suitable low-liquid-level protection should be part of the system design. Keep electrical terminals dry and have the installation checked by a qualified installer.

Are BSP, NPT and metric heater threads interchangeable?

No. These are different thread systems, and a similar diameter or nominal size does not mean the fittings will seal or fit correctly. Check the specified thread family, size, pitch and sealing arrangement on both the heater and the equipment.

DN is a nominal size designation, not a measured outside diameter. For example, do not select a mounting hole or adaptor from a DN label alone. If the thread cannot be positively identified, provide the equipment specification and clear measurements before ordering.

Is every stainless steel heater suitable for drinking water, brewing or pool water?

No. Suitability depends on the complete product, including the sheath, seals, fittings, liquid chemistry and operating conditions. A stainless steel grade by itself is not proof of food-contact, potable-water or pool suitability.

Choose a model whose documentation explicitly supports your application. For salt water, chlorinated water, food or drinking-water contact, confirm compatibility before ordering rather than relying on the product name or appearance.

Loading...
Back to top