HELP CENTRE

Frequently asked questions

Find practical guidance for choosing, installing, and using our products.

QUICK ANSWERS

Featured Questions

How do I choose a replacement heating element?

Compare the original part number and rating label with the replacement specifications. Match voltage, wattage, AC/DC supply and any phase requirements, then check the mounting type, dimensions, material and intended application. A similar appearance alone does not establish compatibility.

If you need help identifying a part, send clear photos of the complete element, its connections and rating label, together with measurements and the equipment model. Isolate the equipment from power before inspecting it.


Can an immersion heater be switched on without liquid?

An element designed for immersion must not be energised with its heated section exposed to air. Keep the required heated length covered by the specified liquid throughout operation, following the product instructions. Dry operation can cause rapid overheating and element failure.

Temperature control and suitable low-liquid-level protection should be part of the system design. Keep electrical terminals dry and have the installation checked by a qualified installer.


How do I check whether a temperature sensor will work with my controller?

Match the sensor technology and the controller's supported input: for example, thermocouple type, RTD type or NTC specification. For NTC sensors, both the resistance at the stated reference temperature and the resistance-temperature curve must match; a 10 kΩ label alone does not establish compatibility.

Check the wiring arrangement, connector, measuring range and probe suitability for the application. Do not assume that sensors with similar plugs or appearances are interchangeable.


Which dimensions should I check before ordering?

Use the dimension drawing for the exact option you intend to buy. Check overall length, insertion length, tube diameter, mounting centres and connection clearance where applicable. For threaded parts, confirm the thread standard, size and pitch; for band heaters, check the inside diameter and band width.

Overall length and heated length may be different. Use millimetres when comparing drawings; 1 inch equals 25.4 mm. If a title, image or option label appears inconsistent, ask us to clarify before ordering.


Can I cut heating cable or heating wire to a shorter length?

It depends on the construction. Some self-regulating cables are designed to be cut to length within specified circuit limits and require approved end seals. Preassembled kits, fixed-length heating cables and resistance wires may have different restrictions.

Shortening a resistance wire changes its electrical characteristics and can make the original supply unsuitable. Do not cut or splice a heating section unless the instructions for that exact product permit it and the revised design has been checked.


Can I use a heater with a different voltage or a higher wattage?

Choose a heater rated for the equipment supply and the specified application. Similar voltage labels do not guarantee that one model is suitable for another supply, and an AC rating does not automatically establish DC suitability. A higher-wattage replacement can also exceed the equipment or control-system rating.

Use the stated operating range and wiring diagram for the selected model. Have a qualified installer confirm any change in voltage, wattage or phase arrangement.


EXPLORE HELP

Browse by topic

Choosing & Ordering
How do I choose a replacement heating element?

Compare the original part number and rating label with the replacement specifications. Match voltage, wattage, AC/DC supply and any phase requirements, then check the mounting type, dimensions, material and intended application. A similar appearance alone does not establish compatibility.

If you need help identifying a part, send clear photos of the complete element, its connections and rating label, together with measurements and the equipment model. Isolate the equipment from power before inspecting it.


Which dimensions should I check before ordering?

Use the dimension drawing for the exact option you intend to buy. Check overall length, insertion length, tube diameter, mounting centres and connection clearance where applicable. For threaded parts, confirm the thread standard, size and pitch; for band heaters, check the inside diameter and band width.

Overall length and heated length may be different. Use millimetres when comparing drawings; 1 inch equals 25.4 mm. If a title, image or option label appears inconsistent, ask us to clarify before ordering.


Can I use a heater with a different voltage or a higher wattage?

Choose a heater rated for the equipment supply and the specified application. Similar voltage labels do not guarantee that one model is suitable for another supply, and an AC rating does not automatically establish DC suitability. A higher-wattage replacement can also exceed the equipment or control-system rating.

Use the stated operating range and wiring diagram for the selected model. Have a qualified installer confirm any change in voltage, wattage or phase arrangement.


View all questions
Immersion Heaters
Can an immersion heater be switched on without liquid?

An element designed for immersion must not be energised with its heated section exposed to air. Keep the required heated length covered by the specified liquid throughout operation, following the product instructions. Dry operation can cause rapid overheating and element failure.

Temperature control and suitable low-liquid-level protection should be part of the system design. Keep electrical terminals dry and have the installation checked by a qualified installer.


Are BSP, NPT and metric heater threads interchangeable?

No. These are different thread systems, and a similar diameter or nominal size does not mean the fittings will seal or fit correctly. Check the specified thread family, size, pitch and sealing arrangement on both the heater and the equipment.

DN is a nominal size designation, not a measured outside diameter. For example, do not select a mounting hole or adaptor from a DN label alone. If the thread cannot be positively identified, provide the equipment specification and clear measurements before ordering.


How do I check whether a tri-clamp heater will fit my vessel?

Compare the heater drawing with the vessel connection, including the ferrule/flange dimensions, clamp and gasket requirements, and the clear opening needed to insert the element. Check the insertion length and allow clearance from the vessel wall, internal coils and other fittings.

Confirm voltage, wattage, phase and the permitted liquid/application as well. The nominal clamp size alone is not enough to establish a complete fit.


View all questions
Industrial Heating Elements
How do I select the correct cartridge heater size?

Check the sheath diameter and tolerance, insertion length, available mounting depth and lead-exit arrangement against the equipment drawing. Also match voltage, wattage and the required temperature-sensor type if one is built in.

The fit between the cartridge and its bore affects heat transfer. Use the heater manufacturer's specified bore tolerance for the application rather than choosing a part solely because it can be pushed into the hole.


Does a cartridge heater with a thermocouple control its own temperature?

An integrated thermocouple provides a temperature signal; it does not by itself switch the heater or regulate its temperature. The heater needs a compatible controller and an appropriately rated switching arrangement.

Confirm the thermocouple type, polarity and wiring diagram, and identify the sensor leads separately from the heater power leads. Do not connect sensor leads to the heater supply.


Can I bend or reshape a tubular heating element?

Only if the exact model is designed for forming and its instructions permit it. Many preformed elements are intended to retain their supplied shape. Bending a finished heater without approved limits can damage its sheath or internal insulation.

For a formable model, obtain the minimum bend radius, permitted forming areas and method before making changes. Do not bend terminals or assume that all products described as tubular or flexible have the same forming limits.


View all questions
Heating Cables & Wire
What is the difference between self-regulating cable and resistance heating wire?

Self-regulating cable changes its heat output in response to its local temperature. Resistance heating wire has an electrical resistance that must be matched to the intended length, supply and heating design. Their sizing and connection requirements are different.

Choose by the exact product type and application, not by appearance. Follow the model's instructions for cutting, termination, insulation and temperature control.


Can I cut heating cable or heating wire to a shorter length?

It depends on the construction. Some self-regulating cables are designed to be cut to length within specified circuit limits and require approved end seals. Preassembled kits, fixed-length heating cables and resistance wires may have different restrictions.

Shortening a resistance wire changes its electrical characteristics and can make the original supply unsuitable. Do not cut or splice a heating section unless the instructions for that exact product permit it and the revised design has been checked.


How do I choose a power supply for low-voltage heating cable?

Match the cable's rated voltage and AC/DC requirements. Size the supply, wiring and protection for the full installed length and the manufacturer's current requirements, including cold-start current for self-regulating cable.

Running wattage alone may underestimate the required supply capacity. For longer runs, account for voltage drop and maximum circuit length. If the product information does not specify startup requirements, confirm them before choosing a supply.


View all questions
Temperature Control & Sensors
How do I check whether a temperature sensor will work with my controller?

Match the sensor technology and the controller's supported input: for example, thermocouple type, RTD type or NTC specification. For NTC sensors, both the resistance at the stated reference temperature and the resistance-temperature curve must match; a 10 kΩ label alone does not establish compatibility.

Check the wiring arrangement, connector, measuring range and probe suitability for the application. Do not assume that sensors with similar plugs or appearances are interchangeable.


Does a wireless thermostat include the receiver and sensor?

Package contents depend on the selected option. A thermostat, receiver and complete kit may be sold separately, and a receiver must be compatible with the thermostat's model and communication system.

Check the selected option and included-items list before ordering. Also confirm the number of zones, sensor requirements and whether the output is suitable for your boiler, heating circuit or control equipment.


Can a temperature controller switch any heater directly?

No. Check the controller output type and its permitted voltage, current and load. The controller's own supply voltage is a separate specification from the load its output can switch. Some outputs are relay contacts; others are signals that require an external switching device.

Use the wiring diagram for the exact model. A suitable contactor or solid-state relay may be needed, with its own ratings and installation requirements. Have the complete arrangement checked by a qualified installer.


Underfloor Heating
How do I choose between underfloor heating film, mats and loose cable?

Choose a system explicitly suitable for the intended floor finish and installation build-up. Check the manufacturer's requirements for the subfloor, insulation, covering layer, moisture conditions and floor-temperature limits. Film, mats and loose cable are not automatically interchangeable.

Confirm the layout and controls before ordering. The floor-finish manufacturer must also allow the selected heating system.


Should I order underfloor heating for the entire floor area?

Base the order on the permitted heated area in a planned layout, rather than the room's total floor area. Follow the system instructions for clearances and exclusions, including fixed units or other areas where heat could be trapped.

Check the specified spacing and cutting restrictions before choosing a size. Do not shorten a mat's heating conductor to make it fit; only cut or alter components where the manufacturer expressly permits it.


Loading...
Back to top